Installing Schluter Shower System

Installing Schluter Shower System – Natural great thing about stone and tile are far liked by most home owners over pre-formed plastic tub surrounds. This is also true in luxury bathroom remodels.

Bathroom renovation companies are taking pleasure in the simplicity of installation that Schluter shower systems offer. Home owners are pleased simply because they facilitate installing a tile or stone shower that’s maintenance-free, sanitary and impervious to water.

Schluter Shower System elements

schluter shower system elements

Schluter Shower Elements

  • 1 – Schluter-KERDI SHOWER TRAY (Schluter-KERDI-SHOWER-ST) – prefabricated tray
  • 2 – Schluter-KERDI SHOWER CURB (Schluter-KERDI-SHOWER-SC) prefabricated curb
  • 3 – Schluter-KERDI-DRAIN – floor drain with a sloped, integrated bonding flange
  • 4 – Schluter-KERDI-BAND Waterproofing strip – for seams
  • 5 – Schluter-KERDI Waterproofing membrane – for walls and floors

Diagram courtesy of Schluter Systems

Fundamental Steps for Installing Schluter Shower System for any Tile Shower

Following the bathroom companies had gutted that old bathroom and roughed within the tub and shower areas the Schluter drain pan might be installed.

1) Unmodified thin-set mortar was spread to the shower substrate floor. Next, the Schluter-KERDI SHOWER TRAY (Schluter-KERDI-SHOWER-ST) was laid and pressed into devote the mattress of thin-set.

2) Next Schluter-KERDI-BAND Waterproofing strip was attached, using thin-set mortar, to each seam in which the wall met the ground and where wall met wall to have a proper seal.

3) After that, the walls where covered Schluter-KERDI Waterproofing membrane. To get this done the walls were troweled with thin-set. Then your thin layer waterproofing material was unrolled within the prepared walls. The advantage of every new bit of waterproofing membrane overlapped the prior piece by 2 “. This sealed all of the walls within the shower area to ensure that they’d be protected against moisture and vapor infiltration.

Read Also :  Design Tips for Small Bathroom Remodeling Ideas

*Note: Schluter-KERDI may be used directly over regular drywall. When installed correctly the waterproof membrane will completely safeguard a tiled shower wall from moisture and water.

4) The Schluter-KERDI-DRAIN was installed and also the waste line was connected. This Schluter floor drain includes a sloped, integrated connecting flange. The whole shower tray then were built with a layer of unmodified thin-set mortar put on its surface. The shower floor ended up being engrossed in the Schluter-KERDI Waterproofing membrane.

5) Then, the Schluter-KERDI SHOWER CURB (Schluter-KERDI-SHOWER-SC) was cut towards the proper length and installed. This curb supplies a ledge which will keep water within the shower and can offer the clear glass door.

6) The KERDI shower curb then had the waterproofing membrane put on it with thin-set. Attention was handed to seal all the junctions in which the curb met the wall and floor.

*Note: Schluter-KERDI-SHOWER curb is made of Expanded polystyrene (broadened polystyrene) foam. It’s 57 psi of compressive strength and may support tile and glass shower doorways.

7) The shower stall ended up being tiled and grouted as always.

8) Finally, the glass walls and clear glass door was installed for that shower. **

Schluter Shower System  Schluter Shower System

Schluter Shower System Diagram

Note : These fundamental steps are just meant use a general outline for implementing a Schluter shower system. Bathroom remodelers, companies and home owners that made a decision to make use of this product for his or her bathroom shower redesign or new installation should stick to the specific directions supplied by the maker. @ Installing Schluter Shower System.